Commercial Demolition Cost in Minneapolis: A Pricing Guide for GCs and Property Managers

Commercial Demolition Cost in Minneapolis

Commercial Demolition Cost in Minneapolis: A Pricing Guide for GCs and Property Managers

Commercial interior demolition in the Minneapolis metro typically runs $4 to $15 per square foot, depending on building type and scope. Light interior demolition for a retail or office tenant improvement lands toward the lower end, while full structural or industrial demolition runs higher due to equipment, permitting, and disposal volume.

Precision Demolition is a licensed and insured demolition contractor serving Minneapolis, St. Paul, and the Twin Cities metro. Our crews are in-house, EPA Lead-Safe Certified, and OSHA 10-trained, and every project is handed back clean and broom-swept, ready for the next trade.

Most commercial demolition pricing online is a national range with no Twin Cities context, published by companies that have never priced a tenant improvement in Minneapolis. General contractors and property managers cannot build a bid on that. You need a per-square-foot band you can carry into an estimate, the factors that move a project inside that band, and the line items that sit outside it, like permits and disposal, so they are budgeted instead of discovered. That is what this guide covers.

What affects commercial demolition pricing in the Twin Cities?

Tenant improvement demolition is the core of commercial interior work in the metro: a space is stripped of the previous tenant’s build-out so new construction can start from a clean shell.

This work prices in the $4 to $15 per square foot band, with light TI scopes, open floor plans, standard partitions, ceiling grid, and finishes, landing toward the lower end. Denser build-outs, multiple enclosed rooms, built-in millwork, restrooms, and kitchen or break room wet areas land higher. The per-square-foot figure covers the demolition labor and equipment to remove the agreed scope and load out the debris; how the full bid breaks down is covered below.

For a GC building a bid, carry the middle of the band for a standard TI scope, then adjust for the factors above once the walkthrough confirms what is actually in the space. A subcontractor who has walked the job will commit to a scoped number rather than a range, and that scoped number is what belongs in your bid. Our Minneapolis commercial demolition contractor page covers how commercial scopes are confirmed before work starts.

Where a project only removes part of a build-out- a single wall line, selected fixtures, a portion of flooring- the pricing logic changes: selective work is slower per foot because everything around the removal has to be protected and preserved. Our selective demolition for tenant improvements page explains how that scope is defined and priced.

Full structural or industrial demolition cost per square foot

Full structural demolition, taking a building or a major structural portion of one down, and heavy industrial demolition price above the interior band, and they are quoted as scoped projects rather than carried on a simple per square foot allowance.

The cost drivers change at this scale. Structural work involves engineering review, shoring and sequencing decisions, heavier equipment, utility disconnections at the service level, and larger disposal volume. Industrial spaces add process equipment, pits, mezzanines, and materials that need characterization before they can be handled or hauled. Permitting is also heavier, as the section below covers.

Because the variables multiply, any per-square-foot figure for structural work published without a site visit is a placeholder, not a price. National sources quote commercial demolition anywhere up to $25 per square foot, which tells you how wide the honest range gets once structure and heavy systems are involved. Get the demolition subcontractor into the pre-bid walkthrough, where structural scope, equipment needs, and disposal can be priced as line items instead of allowances. The estimate you carry should be built from the building, not from a table.

Commercial permitting and disposal costs to budget for

Two cost lines sit outside the demolition price itself, and both belong in the project budget from the start.

Permits. Commercial demolition in Minneapolis runs under city permits, and the City of Minneapolis sets its construction permit fees on a valuation basis, meaning the fee scales with the value of the work. The city’s published permit fee information is the authoritative source for current figures, and it is worth checking at the bid stage because valuation-based fees on a large TI or structural scope are a real number, not a rounding error. On contractor-led projects, the general contractor typically pulls the permit, and the demolition subcontractor works under it, the same arrangement described in our full demolition pricing guide for interior work.

Disposal. Commercial demolition debris is construction and demolition (C&D) waste, priced by volume and weight at the facility that accepts it. A TI strip-out of lightweight partitions and ceiling systems is one disposal profile; concrete, masonry, and structural debris is another, much heavier one. Hauling distance, container turns, and materials needing separate handling all feed the line. In a transparent bid, disposal appears as its own line item with the assumed volume stated, so the GC can see what a scope change would do to it.

Testing. A third line worth naming: pre-demolition hazardous materials testing on older buildings, and regulated abatement where testing finds material that requires it. Neither is demolition, both are often required before demolition can start, and both are cheaper to plan than to improvise mid-schedule.

How commercial demolition bids typically break down

A commercial demolition bid you can build on is a line-item document, not a single lump number. When you receive a bid from a demolition subcontractor, this is what should be visible in it:

Scope and labor. The defined removal scope in plain terms: what comes out, what stays, what is protected, and the labor and supervision required to perform it. If the scope is not written down, the number is not really a bid.

Equipment. The equipment the scope requires, from lifts and loaders to cutting and breaking equipment, is identified separately where it is significant rather than buried in labor.

Protection and site controls. Floor and corridor protection, dust barriers, and any controls needed for occupied-building work. On TI projects in operating buildings, this line is what keeps the neighbors and the landlord whole.

Debris handling and disposal. Loading, containers, hauling, and facility fees, with the assumed volume stated, as covered above.

Handoff condition. The state the space is left in. Our standard is clean and broom-swept, ready for the following trades, as stated in the bid, so there is nothing to negotiate at the end.

Two questions separate a transparent bid from a risky one. First, what is excluded? Permits, testing, and abatement are commonly excluded and budgeted separately, which is fine, as long as the bid says so. Second, how are changes handled? Commercial scopes change when walls open up; a bid that names its change process protects both the GC’s margin and the schedule. A lump sum with neither is the cheapest-looking bid and the most expensive one to own.

Why GCs and property managers choose a dedicated demolition subcontractor over a generalist crew

Demolition is the first scope on site, and the one every other trade’s start date depends on, which is why GCs treat the choice of demolition subcontractor as a schedule decision, not just a price decision.

Schedule reliability. A dedicated demolition contractor staffs your project with its own crews. Precision Demolition’s crews are in-house employees, with no subcontractors, so the crew quoted is the crew that mobilizes, and the completion date in the bid is backed by people the contractor actually controls.

Licensing, insurance, and safety documentation. Commercial clients and landlords require it, and a dedicated subcontractor produces it routinely: licensed and insured, EPA Lead-Safe Certified, and OSHA 10-trained crews, with demolition performed to recognized safety standards.

Bid transparency. As the breakdown above shows, a specialist prices demolition every day and can show the line items a GC needs to defend the number to an owner. A generalist crew pricing demolition as a side scope usually cannot, because the number was never built that way.

Property management continuity. For property managers, the same logic applies across a portfolio: one subcontractor who knows your buildings, prices TI strip-outs consistently from lease to lease, and hands spaces back in the same clean condition every time. Our demolition services page lists the commercial and residential scopes we cover across the metro.

Frequently Asked Questions

How much does commercial demolition cost per square foot in Minneapolis?

Commercial interior demolition in the Minneapolis metro typically runs $4 to $15 per square foot, depending on building type and scope. Light interior demolition for a retail or office tenant improvement lands toward the lower end, while heavier build-outs and scopes approaching structural work land higher.

Small commercial projects are priced within the same $4 to $15 per square foot band, applied to a smaller footprint. A small, open retail or office strip-out prices toward the lower end of the band, while a small space with dense build-out, wet areas, or occupied-building constraints prices higher. The total is set by square footage, scope, and load-out, confirmed at a walkthrough.

A transparent commercial demolition bid itemizes the defined removal scope and labor, equipment, protection and site controls, and debris handling and disposal with the assumed volume stated, and names the handoff condition. Permits, hazardous materials testing, and any regulated abatement are typically excluded and budgeted separately, and the bid should say so.

On contractor-led projects, the general contractor typically pulls the permit and the demolition subcontractor works under it. The City of Minneapolis sets construction permit fees on a valuation basis, so the fee scales with the value of the work and is worth confirming at bid stage.

Interior and tenant improvement demolition is priced per square foot within a band because the scope variables are predictable. Full structural and industrial demolition is quoted as a scoped project because engineering, shoring, heavier equipment, service-level utility disconnections, and much larger disposal volume make a simple per-square-foot figure unreliable without a site visit.

Yes. Precision Demolition works as a demolition subcontractor for general contractors and directly for property managers across the Twin Cities. Crews are in-house, with no subcontractors, and the company is licensed and insured, EPA Lead-Safe Certified, and OSHA 10-trained.

Request a commercial demolition estimate for your Minneapolis project

A per-square-foot bid starts your budget. A scoped bid protects it.

Precision Demolition serves general contractors, property managers, commercial builders, and remodelers across Minneapolis, St. Paul, Edina, Bloomington, Plymouth, Maple Grove, Eden Prairie, Minnetonka, St. Louis Park, Woodbury, Blaine, Lakeville, and Wayzata. Bring us into the pre-bid walkthrough, and you will get a line-item number built from the building, on a schedule our own crews control.

Call 612-517-7680 to request a commercial demolition estimate in Minneapolis-St. Paul.

Bathroom Demolition Cost in Minneapolis: What to Expect in 2026

Bathroom Demolition Cost in Minneapolis

Bathroom Demolition Cost in Minneapolis: What to Expect in 2026

Bathroom demolition in the Minneapolis area typically costs $1,000 to $3,500 for a standard bathroom, with tile removal and fixture disconnection adding the most to the total. A small half-bath demolition runs on the lower end, while a full gut of a tiled, multi-fixture bathroom runs higher.

Precision Demolition is a licensed and insured demolition contractor serving Minneapolis, St. Paul, and the Twin Cities metro. Our crews are in-house, EPA Lead-Safe Certified, and OSHA 10 trained, and every project is handed back clean and broom-swept, ready for the next trade.

Bathrooms are small rooms that price like big ones. Almost every surface is tile, stone, or a fixture, and the materials are some of the heaviest per square foot anywhere in the house. That is why national pricing swings so widely, and why a range with no Twin Cities context tells you very little. This guide gives you the local number, what moves it, and what separates a fixture removal from a full gut.

What affects bathroom demolition cost?

Five things decide almost every bathroom demolition price: the size of the bathroom, how much tile is in it and how that tile was installed, which fixtures are coming out, how deep the demolition goes, and what it takes to disconnect the plumbing safely.

Size and fixture count. A half-bath with a toilet and a pedestal sink is a short job. A master bathroom with a tub, a separate tiled shower, a double vanity, and a toilet is several times the removal, disconnection, and debris, and it is priced accordingly.

Tile and how it was set. Tile is the single biggest cost driver in bathroom demolition. Standard ceramic or porcelain tile on backer board comes out at a predictable pace. Concrete-embedded tile walls, common in older Twin Cities homes, are the most labor-intensive bathroom demolition we do: the tile and its concrete bed have to be broken out together, cleanly, without damaging the surrounding structure. Two bathrooms of the same size can price very differently on this factor alone.

Fixtures. A cast iron tub is heavy and slow to remove compared with a fiberglass tub or shower insert, and stone vanity tops weigh more than laminate. Every fixture is also a plumbing connection that has to be shut off and disconnected in the right order before removal.

Depth of removal. Pulling fixtures and finishes while leaving drywall and subfloor in place is one scope. Taking the room back to bare walls and subfloor is a larger one, and it prices at the top of the range.

Age of the home. Pre-1980 Twin Cities homes can require testing for asbestos or lead paint before demolition begins, and any testing or regulated abatement is budgeted separately from the demolition price. Finding that at the quote stage is far cheaper than finding it mid-project.

Disposal and access. Bathroom debris is dense: tile, concrete bed, cast iron, and stone all weigh far more than their size suggests, so hauling and disposal are real line items. An upstairs bathroom at the end of a finished hallway also takes longer to load out, and protecting those finished surfaces on the way through is part of the work, not an extra.

National sources such as Angi put bathroom demolition anywhere from $658 to $2,469, or roughly $8 to $20 per square foot, and that spread is exactly the problem: it mixes half-baths with master suites and fixture pulls with full guts. The $1,000 to $3,500 range above is the Twin Cities planning band for a standard bathroom handled by a licensed local crew.

Cost to remove a tub, vanity, and toilet only

The smallest bathroom demolition scope is a fixture removal: tub or shower unit, vanity, and toilet out, with the tile, flooring, and walls left in place for the remodel that follows.

This is the right scope when the layout and surfaces are staying and only the fixtures are being replaced. Because each fixture is disconnected and removed without breaking out tile or drywall, this scope sits at the low end of the range. For a standard bathroom it forms the lower portion of the $1,000 to $3,500 band, and a half-bath with only a toilet and sink to pull can come in below the standard range entirely.

What the work involves: water shut off to the bathroom, fixtures disconnected in sequence, the tub or shower unit, vanity, and toilet removed and carried out, and the room left clean with capped lines ready for the plumber or the next trade. A cast iron tub takes longer and needs more hands than a fiberglass insert, and a stone vanity top handles differently than a laminate one, so both are worth settling at the quote stage rather than on the day.

Our Minneapolis bathroom demolition services page covers how this scope is confirmed before work starts, so the fixtures you expect out are exactly the ones that come out.

Cost for a full bathroom gut (tile, subfloor, fixtures, drywall)

A full bathroom gut takes the room back to bare walls and subfloor: wall and floor tile, tub or shower, vanity, toilet and fixtures, drywall and backer board, and subfloor where the agreed scope includes it.

This is the scope behind the top of the range. A standard bathroom gutted completely prices toward the upper end of the $1,000 to $3,500 band, and a large master bathroom with concrete-embedded tile can price as a larger project once scoped. The drivers stack up quickly: tile breakout is the slowest work in the room, a full gut removes all of it, and every layer under the tile adds labor and debris weight.

A full gut is the right scope when the remodel changes the layout, replaces the tile and flooring, opens walls for new plumbing, or follows water damage that has reached the subfloor or wall cavities. It also makes the rest of the remodel more predictable, because framing, plumbing, and subfloor are fully exposed for inspection before anything new is built. Rot, old galvanized plumbing, and outdated wiring are cheapest to deal with at exactly this moment.

One caution when comparing bids at this scope: make sure every quote describes the same endpoint. A gut priced to the studs and subfloor is not comparable to one that stops at fixture removal with the tile left down, and the cheaper number usually turns out to be the smaller scope. For how a single-room gut fits into whole-home pricing, see our interior demolition cost guide.

Small/half-bath vs. full/master bathroom demolition cost

Bathroom demolition prices by scope first and size second, but size still sets the frame, and the Twin Cities housing stock covers both ends of it.

A half-bath is the least expensive bathroom demolition there is. With a toilet, a small vanity or pedestal sink, and little or no tile, there is simply less to disconnect, break out, and haul, and a half-bath demolition prices at or below the bottom of the standard range.

A standard full bathroom, one tub or shower, one vanity, one toilet, tiled floor and tub surround, is what the $1,000 to $3,500 range describes. Where it lands inside the band is decided by tile installation method, teardown depth, and fixture materials rather than square footage alone.

A master bathroom prices at and above the top of the standard band. Separate tub and shower, double vanity, and more tile on more surfaces all add up, and a master suite gut should be budgeted as its own scoped project rather than estimated off the standard range. The honest way to price one is a walkthrough or photos with measurements, because the difference between standard tile and concrete-embedded tile walls is measured in labor hours, not percentages.

Kitchens and bathrooms are often demolished together in the same remodel. If your project covers both rooms, our kitchen demolition page prices that side of the work, and scoping both rooms in one visit usually gives a cleaner combined number.

Do you need to shut off plumbing before demolition? What's included in a pro quote

Yes, and it is handled as part of the job, not left to you. Before any fixture comes out, the water supply to the bathroom is shut off, and the fixtures are disconnected in the right order. Lines are capped so the rest of the house can keep its water on, and the sequence is coordinated with the general contractor or plumber on contractor-led projects. This is one of the clearest lines between a demolition quote and a simple removal price: a crew that cannot manage the shutoff properly can hand you a leak inside a wall you were not planning to open.

A standard Precision Demolition quote includes scope confirmation before work begins, protection for the rest of the home, the demolition itself, debris loading and disposal, and a clean handoff. The protection line deserves its own mention in a bathroom project, because the work zone is almost always reached through finished rooms: Ramboard or Masonite goes down on hallways and finished floors, and plastic dust barriers go up at doorways. The bathroom is small; the path to it usually is not, and an unprotected demo tracks grit across all of it.

Homeowners pricing a DIY bathroom demo usually count only their own labor and miss the rest: disconnecting plumbing without damaging lines that stay, breaking out tile and concrete bed without the right tools, renting disposal capacity for debris that is much heavier than it looks, and the cleanup at the end. They also carry the risk lines. A cracked supply line, a damaged flange, or a gouged subfloor that was supposed to stay comes straight out of the remodel budget. Permits remain the responsibility of the homeowner or their general contractor either way: on contractor-led projects the general contractor pulls the permit, and Precision Demolition operates as a licensed subcontractor under it.

DIY fixture removal can make sense on a small, simple scope. Once the project reaches tile breakout, a full gut, or concrete-embedded tile, the gap between the DIY estimate and the professional quote narrows fast, and the professional quote comes with the shutoff, protection, disposal, and cleanup already handled.

How long does bathroom demolition take?

A standard bathroom demolition takes 4 to 8 hours, depending on size and scope.

A fixture removal sits at the shorter end of that window. A full gut runs longer, and concrete-embedded tile walls or a large master bathroom can push past it, something we scope out with you before the project begins. Either way, bathroom demolition is measured in hours, not days or weeks, which is why it is scheduled as the first step of a bathroom remodel rather than a phase of its own.

The timeline that matters is the one after the demo: the room is handed back clean and broom-swept, ready for plumbing, framing, and tile trades to start immediately. A demo that runs long or leaves debris behind delays every trade behind it, and in a one-bathroom home it also decides how long the household is without the room. Before the crew arrives, the homeowner’s only job is to clear personal items out of the bathroom, so a bathroom that starts empty and scoped is one that finishes on the 4- to 8-hour pace.

Frequently Asked Questions

How much does small bathroom demolition cost in Minneapolis?

A small bathroom or half-bath is the least expensive bathroom to demolish because there are fewer fixtures to disconnect and little or no tile to break out. Small bathroom demolition prices at or below the bottom of the $1,000 to $3,500 standard bathroom range in the Twin Cities, with the exact figure set by whether the scope is fixture removal only or a full gut.

A master bathroom is priced at or above the top of the $1,000 to $3,500 standard bathroom range. A separate tub and shower, a double vanity, and more tile on more surfaces add labor and debris weight, and concrete-embedded tile walls add more. Master bathroom demolition is priced from a walkthrough or photos with measurements rather than estimated from the standard range.

A full bathroom gut removes wall and floor tile, the tub or shower, vanity, toilet and fixtures, drywall and backer board, and subfloor where the agreed scope includes it, taking the room back to bare walls and subfloor. Plumbing is shut off, and fixtures are disconnected as part of the work, and debris loading and disposal are included in a standard Precision Demolition quote.

The water supply to the bathroom is shut off, and fixtures are disconnected in sequence as part of a professional demolition, with lines capped so the rest of the house keeps its water. You do not need to shut anything off yourself; the homeowner’s only preparation is clearing personal items out of the bathroom.

A standard bathroom demolition takes 4 to 8 hours, depending on size and scope. Fixture removal is on the shorter end, and a full gut with tile breakout or concrete-embedded tile walls takes longer.

DIY saves the labor line and adds back dumpster rental and disposal fees, tool costs, floor protection, and your own cleanup time. It also carries the risk of plumbing or subfloor damage coming out of the remodel budget. On a fixture-only scope, the savings can be real; on a full gut with tile breakout, the gap to a professional quote is usually much smaller than expected.

Get a bathroom demolition quote in Minneapolis-St. Paul

A range starts your budget. A scoped quote gets your project scheduled.

Precision Demolition serves general contractors, remodelers, restoration companies, investors, and homeowners across Minneapolis, St. Paul, Edina, Bloomington, Plymouth, Maple Grove, Eden Prairie, Minnetonka, St. Louis Park, Woodbury, Blaine, Lakeville, and Wayzata. Every crew is in-house, and every bathroom is handed back clean and broom-swept, ready for the next trade.

Call 612-517-7680 for a kitchen demolition quote in Minneapolis-St. Paul.
Email: zubin@precisiondemolition.net
Request a Project Quote: Click Here

You can find our Better Business Bureau Profile here!

Kitchen Demolition Cost in Minneapolis: 2026 Pricing Breakdown

Kitchen Demolition Cost in Minneapolis

Kitchen Demolition Cost in Minneapolis: 2026 Pricing Breakdown

Kitchen demolition in Minneapolis typically costs $800 to $2,600 for a standard kitchen, and $500 to $3,800 across the full range of sizes and scopes. Removing cabinets and countertops only costs less than a full teardown that includes flooring, drywall, and plumbing and electrical disconnection.

Precision Demolition is a licensed and insured demolition contractor serving Minneapolis, St. Paul, and the Twin Cities metro. Our crews are in-house, EPA Lead-Safe Certified, and OSHA 10 trained, and every project is handed back clean and broom-swept, ready for the next trade.

Search for kitchen demolition cost and most of what you find is national pricing with no Twin Cities context, or removal pricing from companies that haul debris but do not do demolition work. Neither tells you what a licensed local crew actually charges to take a Minneapolis kitchen apart. This guide does: what kitchen demolition costs here in 2026, what moves the number up or down, what a professional quote includes, and how the scope you choose changes the price more than the size of the room does.

What affects kitchen demolition cost?

Four things decide almost every kitchen demolition price: the size of the kitchen, how deep the demolition goes, what the kitchen is made of, and how much debris has to leave the house.

Size and layout. A compact galley kitchen has fewer cabinets, less countertop, and less flooring than a large open-concept kitchen with an island. More material to remove means more labor hours and more disposal volume, and both are priced into the quote.

Depth of removal. Cabinet and countertop removal is one scope. Taking the room back to the studs and subfloor is a different one. Every layer added between those two points, flooring, drywall, fixtures, adds time and debris, and moves the price up the range.

Materials. Tile flooring, stone countertops, and plaster walls are heavier and slower to remove than laminate, butcher block, and drywall. Older Twin Cities kitchens often stack several of these together, which is why two kitchens of the same size can price quite differently.

Plumbing and electrical disconnection. A teardown that reaches fixtures and appliances involves disconnecting plumbing and electrical lines before removal. That disconnection is coordinated with the licensed trades, and it is part of what separates a demolition quote from a simple haul-away price.

Disposal. Everything that comes out has to be loaded, hauled, and disposed of. Kitchens produce dense, heavy debris, and the roll-off dumpster and disposal volume are real line items in a professional quote, not afterthoughts.

Age of the home. As with any interior demolition in Minneapolis and St. Paul, older homes can require testing for asbestos or lead paint before work begins, and any testing or regulated abatement is budgeted separately from the demolition price. It is far cheaper to identify that at the quote stage than mid-project.

Access and staging. Where the kitchen sits in the house affects how fast debris moves out of it. A first-floor kitchen with a short path to the roll-off dumpster loads out faster than an upper-level kitchen, a tight stairwell, or a home where the dumpster has to sit far from the door. Access rarely changes which end of the range a job lands on by itself, but combined with heavy materials and a full teardown scope, it is one of the reasons two similar kitchens do not price the same.

Cost to remove cabinets and countertops only

This is the scope homeowners and general contractors choose when the flooring, walls, and layout are staying, and only the cabinetry is being replaced. Because nothing is disconnected beyond the sink fixtures and nothing structural is touched, it sits at the low end of the overall kitchen demolition range. Within the $500 to $3,800 spread for kitchen demolition in the Twin Cities, cabinet and countertop removal is where the bottom of that range lives, and for a standard kitchen it forms the lower portion of the $800 to $2,600 band.

What the work involves: cabinet boxes and doors removed from walls and base runs, countertops detached and carried out, the area cleared of debris, and the room left clean for the cabinet installer or the next trade. Islands and long countertop runs add time, and stone tops add weight and handling, so a large kitchen’s cabinet removal can price above a small kitchen’s full teardown. Scope and size always price together.

If this is the scope you are planning, the fastest way to a real number is a walkthrough or a set of photos with measurements. Our Minneapolis kitchen demolition services page covers how that scope is confirmed before work starts, so the price you are quoted is the price the job runs at.

Cost for a full kitchen teardown (cabinets, flooring, drywall, fixtures)

A full kitchen teardown takes the room back to the studs and subfloor: cabinets and countertops, flooring, drywall or plaster, and fixtures all come out, with plumbing and electrical disconnection coordinated before removal.

This is the scope behind the top of the range. A standard kitchen torn down completely prices toward the upper end of the $800 to $2,600 band, and a large kitchen with heavy materials can reach the top of the overall $500 to $3,800 spread. The drivers are the ones you would expect: tile or multiple flooring layers take longer to break out than a single layer of vinyl or laminate, plaster is slower than drywall, and every fixture removed is a disconnection that has to happen in the right order.

A full teardown is the right scope when the remodel changes the layout, replaces the flooring, or opens walls for new plumbing and electrical runs. It is also the scope that makes the rest of the remodel faster, because the framing and subfloor are fully exposed for inspection before anything new is built. If damage, outdated wiring, or old plumbing is hiding in the walls, the teardown is when you find it, while it is still cheap to address.

Appliances are part of the teardown conversation. Ranges, dishwashers, and refrigerators have to be disconnected and moved out before or during demolition, and that removal is coordinated with the general contractor or homeowner as part of the confirmed scope. What gets saved for reuse, what gets hauled with the debris, and what the homeowner is removing themselves should all be settled before the crew arrives, because appliance decisions made mid-demo are the ones that slow a teardown down.

One caution on comparing bids at this scope: make sure every quote describes the same endpoint. A teardown priced to the studs is not comparable to one that stops at cabinet removal with the flooring left down, and the cheaper number usually turns out to be the smaller scope. For how single-room kitchen work fits into whole-home pricing, see our full interior demolition cost guide, which prices interior demolition per square foot across every room type.

Small kitchen vs. large/open-concept kitchen demolition cost

Size changes a kitchen demolition price less than scope does, but it still matters, and it matters most at the two ends of the housing stock.

A small kitchen, the galley and L-shaped kitchens common in older Minneapolis and St. Paul homes, is the least expensive demolition in this category. Fewer cabinets, shorter countertop runs, and less flooring keep labor and disposal low, and a small kitchen demolition prices toward the bottom of the range, whether the scope is cabinet removal or a full teardown.

A large or open-concept kitchen prices toward the top. There is simply more of everything: longer cabinet runs, an island, more countertop material, more flooring square footage, and more debris to load out. Open-concept projects also raise a question small kitchens rarely do, whether a wall is coming out as part of the demolition. Removing a wall is a bigger scope than removing finishes, and where the wall carries structure, the work has to be sequenced with your general contractor rather than treated as standard demolition. If your project includes wall removal, expect it to be scoped and priced separately from the kitchen teardown itself.

Most kitchens, of course, sit between those ends. A mid-size kitchen with a standard cabinet run, one flooring layer, and no wall work is exactly what the $800 to $2,600 standard range describes, and where it lands inside that band is decided by teardown depth and materials rather than by square footage alone.

The practical takeaway: use the $500 to $3,800 range as the planning band, expect small kitchens with light scopes near the bottom and large open-concept teardowns near the top, and treat any exact figure given without seeing the kitchen as an estimate, not a quote.

What's included in a professional kitchen demo quote, and what's often missed by DIY?

A professional kitchen demolition quote covers more than the removal itself. A standard Precision Demolition quote includes scope confirmation before work begins, protection for the rest of the home, the demolition, debris loading and disposal, and a clean handoff.

The protection line is the one people underestimate. Floors in adjacent rooms and traffic paths are covered with Ramboard or Masonite sheeting, and plastic dust barriers go up at doorways and openings so demolition dust stays in the work zone. The kitchen is the most connected room in the house, and an unprotected demo sends dust and grit through all of it.

Homeowners pricing a DIY kitchen demo usually count only their own labor, which is free, and miss the rest of the list: renting a roll-off dumpster and paying disposal fees, disconnecting plumbing and electrical safely, protecting floors and containing dust, appliance removal coordination, and the dump runs and cleanup time at the end. They also carry the risk lines. A cut line, a cracked pipe, or damage to flooring that was supposed to stay comes straight out of the remodel budget, and permits remain the responsibility of the homeowner or their general contractor either way, since demolition permits are pulled by the general contractor on contractor-led projects and a licensed demolition subcontractor works under that permit.

DIY cabinet removal can make sense on a small, simple scope. Once the project reaches flooring, drywall, fixtures, and disconnections, the gap between the DIY estimate and the professional quote narrows fast, and the professional quote comes with the protection, disposal, and cleanup already handled.

How long does kitchen demolition take?

Most kitchen demolition projects take 4 to 8 hours, depending on scope.

A cabinet and countertop removal sits at the shorter end of that window. A full teardown back to the studs, with flooring broken out and fixtures disconnected, runs longer, and a large open-concept kitchen can push past it. Either way, kitchen demolition is measured in hours and days, not weeks, which is why it is scheduled as the first step of a kitchen remodel rather than a phase of its own. For a step-by-step look at sequencing, see what to expect during demolition.

The timeline that matters is the one after the demo: the room is handed back clean and broom-swept, ready for framing, plumbing, and electrical trades to start immediately. A demo that runs long or leaves debris behind delays every trade scheduled behind it.

Before the crew arrives, the homeowner’s only job is to clear personal items out of the kitchen. Permits and utility coordination are handled by the general contractor on contractor-led projects, so a kitchen that starts empty and scoped is a kitchen that finishes at a 4 to 8-hour pace.

Frequently Asked Questions

How much does it cost to remove kitchen cabinets and countertops?

Cabinet and countertop removal is the smallest kitchen demolition scope and is priced at the low end of the kitchen demolition range. Kitchen demolition in Minneapolis runs $500 to $3,800 overall, depending on size and scope; a standard kitchen typically costs $800 to $2,600, and cabinet and countertop removal falls at the lower end of that range.

A small kitchen is the least expensive to demolish because it has fewer cabinets, shorter countertop runs, and less flooring to remove and dispose of. Small kitchen demolition prices are toward the bottom of the $500 to $3,800 Twin Cities range, with the exact figure set by whether the scope is cabinet removal only or a full teardown to the studs.

Most kitchen demolition projects take 4 to 8 hours, depending on scope. Cabinet and countertop removal is on the shorter end, and a full teardown back to the studs and subfloor takes longer.

The general contractor pulls the permit on contractor-led projects, and Precision Demolition operates as a licensed subcontractor under the general contractor’s permit. Homeowners running their own project should confirm their city’s requirements before work starts.

Yes. A standard Precision Demolition quote includes loading, hauling, and disposal of the debris created by the confirmed scope, with roll-off dumpster service coordinated when the project needs it. Always confirm disposal is included in any bid you compare, because leaving it out is the easiest way to make a bid look cheaper.

Get a kitchen demolition quote in Minneapolis-St. Paul

A range gets your budget started. A scoped quote gets your project scheduled.

Precision Demolition serves general contractors, remodelers, restoration companies, investors, and homeowners across Minneapolis, St. Paul, Edina, Bloomington, Plymouth, Maple Grove, Eden Prairie, Minnetonka, St. Louis Park, Woodbury, Blaine, Lakeville, and Wayzata. Every crew is in-house, and every kitchen is handed back clean and broom-swept, ready for the next trade.

Call 612-517-7680 for a kitchen demolition quote in Minneapolis-St. Paul.
Email: zubin@precisiondemolition.net
Request a Project Quote: Click Here

You can find our Better Business Bureau Profile here!

7 Signs Your Minneapolis Home Needs a Full Gut, Not Just a Remodel

Full Gut Remodel

7 Signs Your Minneapolis Home Needs a Full Gut, Not Just a Remodel

A full-house gut is usually the right call when a home has structural issues, outdated systems throughout (knob-and-tube wiring, galvanized plumbing, an undersized electrical panel), or widespread water or mold damage. If the problems are isolated to one room, a partial or selective demolition is typically enough.

By Precision Demolition, a licensed and insured demolition contractor serving Minneapolis, St. Paul, and the Twin Cities metro. Our crews are in-house, EPA Lead-Safe Certified, and OSHA 10-trained, and every project is handed back clean and broom-swept, ready for the next trade.

Every older Twin Cities home reaches a decision point. You can remodel around what is already there, or you can take the interior back to the studs and start clean. Remodeling over problems that run through the whole house just buries them behind new finishes, where they cost more to fix later. The seven signs below are the ones that point to a gut. One sign on its own might not settle it. Several together almost always do.

Sign 1 - Outdated electrical (knob-and-tube or aluminum wiring, common in older Twin Cities homes)

Knob-and-tube wiring is common in pre-1950s Minneapolis and St. Paul homes, and aluminum wiring shows up in homes built in the decades after. Neither was designed for the load a modern household puts on it, and both tend to run through the entire house rather than one room.

If the wiring is outdated everywhere, and the electrical panel is undersized for the renovation you are planning, patching one circuit at a time does not solve the problem. Opening every wall in a full gut is what lets an electrician replace the system completely instead of working around finishes you are trying to save.

Sign 2 - Galvanized or original plumbing throughout

Galvanized plumbing has a working life, and in older Twin Cities housing stock that life is often spent. When the original galvanized pipes run throughout the house, corrosion and narrowing are not a one-bathroom problem. They are a whole-house problem that shows up as weak pressure and discolored water in more than one place.

Replacing plumbing room by room, through finished walls, is slow and expensive. In a gut, the walls are already open, the old pipe comes out with the rest of the demolition, and the plumber starts from clean framing.

Sign 3 - Structural wear or an undersized foundation for the home's age

Some problems are cosmetic. Structural wear is not. A foundation that is undersized for the home built on it, framing that has shifted or deteriorated with age, and floors that tell you the structure has moved are all signs that the house needs more than new finishes.

Structural questions have to be answered before a remodel is designed, not discovered during one. If you are unsure what you are looking at, a home inspection is the right first step: the American Society of Home Inspectors is a good general resource for finding an inspector and understanding what an inspection covers. When the structure itself needs attention throughout, gutting gives every trade full access to the framing and the foundation walls.

Sign 4 - Widespread water damage or mold, not isolated to one area

A single leak under one sink is a repair. Water damage or mold in the bathroom, the basement, and around windows on more than one floor is a pattern, and a pattern means the source has been at work for a long time.

Mold and water damage hide behind finishes, so the visible area is rarely the whole area. A gut exposes everything at once, so damaged material comes out completely instead of being sealed behind new drywall. This is also work that has to be handled carefully, which is why our crews work to our safety standards on every interior project, and why Precision Demolition carries EPA Lead-Safe Certification for older housing stock.

Sign 5 - A layout that can't be fixed without opening walls

Some floor plans cannot be saved by moving a doorway. If the layout you need means removing or relocating walls across the main floor, including a load-bearing wall that currently carries the structure above it, the project is already most of the way to a gut.

At that point, selective demolition room by room often costs more in time and patching than it saves. Taking the interior down to the studs in one pass lets the new layout be framed cleanly, and load-bearing changes can be sequenced properly with your general contractor instead of improvised wall by wall.

Sign 6 - The home sat vacant or was neglected for years

A house that sat vacant or was neglected for years deteriorates in ways a quick walkthrough understates. The signs of a neglected house tend to stack up: water intrusion that was never dried out, systems that were never maintained, finishes damaged in several rooms at once, and small problems in every system instead of a big problem in one.

Neglect is rarely isolated, and that is the point. When every room needs attention and every system is suspect, there is little left worth remodeling around. A gut turns an unknown quantity into a known one, because everything hidden is exposed and assessed before rebuild money is spent.

Sign 7 - You're already planning a full renovation and want to start clean

Sometimes the house decides for you, and sometimes the scope does. If you are already planning a full renovation, new systems, a new layout, and new finishes throughout, then the existing interior is coming out anyway.

In that case, a full gut is simply the efficient version of the same project. One demolition phase, quoted per project after a walkthrough, replaces months of piecemeal removal between trades. For what that phase runs in the Twin Cities, see our full house gut cost guide: the demolition portion on an average single-family home typically runs $15,000 to $35,000, and a full gut typically takes 2 to 4 weeks from mobilization to handoff.

Full gut vs. selective demolition - how to tell which you need

Use one test: is the problem in one place, or is it the house?

If the electrical, plumbing, structure, and finishes are sound and only one room is being changed, selective demolition is the right scope. That is the single-room work priced per square foot in our interior demolition cost guide, typically $2 to $8 per square foot depending on what is being removed. If the signs above show up in combination- outdated systems throughout, damage in more than one area, a layout that has to open up anyway- then a selective scope just delays the gut and charges you for demolition twice.

When you are ready to price the whole-house option properly, start with our house gut demolition services and a walkthrough. A contractor who walks the house can tell you which side of the line it sits on and quote the demolition in writing, room by room.

Frequently Asked Questions

What are the signs of a neglected house?

Water damage in more than one area, systems that have not been maintained, damaged finishes across several rooms, and deterioration that shows up in the structure as well as the surfaces. One neglected item is a repair. A house full of them is a gut candidate, because the problems are connected rather than isolated.

Demolition comes first, then structural and framing work, then the mechanical systems (electrical, plumbing, and HVAC), then insulation and drywall, then finishes. That order is exactly why the gut decision matters at the start: the demolition scope determines what every trade after it can do, and when they can start.

For the demolition portion alone, an average single-family home in the Twin Cities typically runs $15,000 to $35,000, quoted per project after a walkthrough rather than off a per-square-foot rate. The full breakdown is in our house gut cost guide, linked above.

Talk to a Minneapolis demolition contractor before you decide

You do not have to settle the gut versus remodel question from an article. A walkthrough settles it in person.

Precision Demolition serves general contractors, remodelers, restoration companies, and homeowners across Minneapolis, St. Paul, Edina, Bloomington, Plymouth, Maple Grove, Eden Prairie, Minnetonka, St. Louis Park, Woodbury, Blaine, Lakeville, and Wayzata. See our service areas for the full list. Every crew is in-house, with no subcontractors, and every gut is handed back clean and broom-swept, ready for the next trade.

Call 612-517-7680 to talk through your Minneapolis home before you decide.

Full House Gut Cost in Minneapolis: What You’ll Actually Pay in 2026

Full House Gut Cost

Full House Gut Cost in Minneapolis: What You'll Actually Pay in 2026

Gutting a house down to the studs in the Minneapolis metro typically costs $15,000 to $35,000 for the demolition portion alone on an average single-family home, separate from the remodel that follows. The exact number depends on square footage, whether you are removing to the studs or further, and how much of the home has hazardous materials that require abatement.

By Precision Demolition, a licensed and insured demolition contractor serving Minneapolis, St. Paul, and the Twin Cities metro. Our crews are in-house, EPA Lead-Safe Certified, and OSHA 10-trained, and every gut project is handed back clean and broom-swept, ready for the next trade.

Search for house gut cost, and most of what you find is remodel pricing wearing a demolition label. National sites and remodeling companies quote the full project, demolition plus rebuild, as one number, which is why the figures online swing so wildly and why Twin Cities homeowners and investors keep asking what the gut itself actually costs. This guide isolates the demolition line item: what a professional full house gut costs in Minneapolis and St. Paul, what drives that number up or down, and what you should budget for separately.

What's the difference between 'gut cost' and 'remodel cost'?

These two numbers get confused constantly, and they are not the same purchase.

The gut cost is the demolition portion only. It pays for a trained crew to take the interior of the house apart: drywall and plaster, flooring, cabinetry, bathroom finishes, fixtures, and interior trim, removed down to the studs and subfloor, loaded out, hauled away, and disposed of. When the gut is finished, you own an empty, clean structure. Nothing has been rebuilt yet.

Remodel cost is everything after that. Framing changes, electrical, plumbing, HVAC, insulation, drywall, flooring, cabinets, tile, paint, and finishes. On a full renovation, the remodel portion is several times the size of the gut portion, and it is where most of the figures quoted online actually live. When a website tells you a gut remodel costs a large per-square-foot figure, nearly all of that figure is rebuild work, trades, and materials, not demolition.

Why does the separation matter? Because the gut is the first line item chronologically and the one everything else schedules around. A general contractor building a realistic project budget prices the demolition phase on its own, the way it is broken out in our full demolition cost guide. Investors running numbers on a flip or a rehab need the same separation, because a wrong gut figure distorts the whole deal.

How much does it cost to gut a house down to the studs in Minnesota?

For the demolition portion alone, an average single-family home in the Minneapolis-St. Paul metro typically runs $15,000 to $35,000. That range covers a complete interior gut to the studs: every room, every finish, taken back to bare framing and subfloor, with debris hauled and disposed of.

Two things about that range are worth understanding before you use it.

First, a whole-house gut is not quoted off a simple per-square-foot rate. Single-room interior demolition can be estimated per square foot, because the scope is one space with a defined set of finishes. A full house gut is dozens of scopes stacked together: plaster in one room and drywall in another, tile bathrooms, a finished basement, insulation, multiple flooring types, and far more disposal volume than any single room produces. Depth of scope matters as much as area. Removing finishes to the studs is one job; also taking ceilings, subfloor, or specific structural elements is a bigger one. For that reason, whole-house pricing is quoted per project, after a walkthrough, not from a rate card. A firm whole-house number given without a walkthrough is a guess.

Second, age changes everything in the Twin Cities. Minneapolis and St. Paul housing stock includes a large share of older homes with plaster and lath, layered flooring, and, in homes built before 1980, the real possibility of asbestos and lead paint. Those materials slow the work down and can require abatement before or during demolition, which is why two houses of identical square footage on the same street can land far apart in the range.

The most reliable way to price a gut is to have a contractor scope it in person, room by room, and quote it in writing. That is how a Minneapolis house gut contractor should be pricing your project, and it is the number you can safely build a remodel budget on top of.

What affects house gut demolition pricing?

Four factors explain most of the spread between the low and high ends of the range, and every one of them is visible on a walkthrough.

Square footage and layout. Size is the starting point. More interior area means more material to remove, more labor hours, and more debris. Layout compounds it: a two-story home with a finished basement and an attic conversion holds far more demolishable interior than a single-story home of the same footprint.

What the house is made of. Plaster and lath, common in older Minneapolis and St. Paul homes, is heavier and slower to take down than modern drywall. Tile set in mortar beds, stone, real hardwood under layers of later flooring, and cast iron tubs all add labor and weight. A house finished in drywall and carpet guts faster and cheaper than one finished in plaster, tile, and hardwood.

Hazardous materials. If testing finds asbestos or lead paint, the affected materials need regulated handling, and abatement can become its own line item before general demolition proceeds. Precision Demolition is an EPA Lead-Safe Certified firm, so lead-regulated work is handled correctly in-house, but the scope and the cost still belong in the quote, not in a surprise change order. The Minnesota Pollution Control Agency asbestos guidance sets out how asbestos is regulated in Minnesota before renovation and demolition work.

Access and disposal. Everything removed has to leave the house and the property. Tight lots, narrow stairwells, upper-floor work, and limited space for a roll-off dumpster all slow the load-out. Disposal is a major cost driver: a full gut uses serious dumpster capacity, and heavy materials like plaster, tile, and masonry cost more to haul and dispose of than lightweight drywall. When you compare bids, confirm that hauling and disposal are inside the quoted number.

Structural elements sit across all four factors. If the remodel plan removes or moves a structural wall, the demolition crew coordinates the sequence with your general contractor, and the framing work that supports or rebuilds that wall is a separate trade scope, priced by the framing side, not buried in the gut price.

House gut cost by home size

Size is the easiest planning lever, so use the table below to place your project in the range. These are planning positions anchored to the $15,000 to $35,000 range for an average single-family home, not quotes. Finishes, age, and hazardous materials move a specific house within, or beyond, its row.

Home size

Where it typically lands

1,000 sq ft

Low end of the range or below it. Less interior to remove and less disposal volume, so a lighter scope in a newer home sits at the bottom of the pricing picture.

1,500 sq ft

The middle of the $15,000 to $35,000 range. This is close to the average single-family scope the range was built on, with typical finishes and no major abatement.

2,000+ sq ft

Upper end of the range, and larger or heavier homes can go above $35,000, especially with plaster, multiple bathrooms, a finished basement, or abatement in scope.

 

A 1,200 sq ft house, a size homeowners ask about often, sits between the first two rows: smaller than the average home behind the range, so most 1,200 sq ft guts price toward the lower portion of it when the scope is light and no regulated materials are involved.

However, your home lands in the table, treat the figure as a budget anchor for the demolition phase, then replace it with a written, per-project quote before you commit to a remodel budget or a closing date.

What's included in a professional house gut, and what should you budget separately?

A professional full house gut from a licensed contractor should include the complete removal scope, executed in one sequenced pass:

  • Drywall and plaster, walls and ceilings, taken back to the studs
  • All flooring, including carpet, hardwood, tile, and vinyl, down to the subfloor, and subfloor removal where the scope specifies it
  • Kitchen cabinetry and countertops, and the full kitchen and bathroom demolition scope inside the whole-house project
  • Every bathroom finish: tile, tubs and showers, vanities, toilets, and fixtures
  • Interior doors, trim, and hardware included in the scope
  • Insulation where the demolition exposes it
  • Protection for anything that stays, and a clean, broom-swept structure at handoff
  • Loading, hauling, and disposal of the debris the scoped work creates

Budget these items separately, because they are not part of the demolition line item:

  • The remodel itself. Framing, mechanical trades, insulation, drywall, and all finish work start where the gut ends, and they are the large majority of a full renovation budget.
  • Hazardous material abatement. Testing and any regulated abatement the testing triggers is priced as its own item. In pre-1980 Twin Cities homes, ask about it at the quote stage.
  • Structural wall modifications. Supporting, removing, or rebuilding a load-bearing or structural wall is framing and engineering work, arranged through your general contractor. The demolition crew coordinates the sequence, but the modification is not a demolition cost.
  • Permit fees. On contractor-led projects, the general contractor pulls the permits, and the demolition crew operates under them. Fees are set by the city and belong to the project budget.
  • Disposal beyond the scoped volume. If the project uncovers materially more debris than the walkthrough scope, such as hidden layers of flooring or concealed debris, that extra volume is confirmed in writing before it is billed.

This separation is also why in-house crews protect your number. Precision Demolition runs gut projects with its own employees and no subcontractors, so the crew on site is working from the scope you signed.

How long does a full house gut take in the Twin Cities?

A full interior gut typically takes 2 to 4 weeks from mobilization to handoff, depending on the size of the structure and the scope inside it. A smaller, single-story home with light finishes sits at the fast end. A large, multi-story home with plaster, heavy finishes, phased work, or hazardous materials requiring abatement takes longer, and that timeline is scoped with your general contractor before work begins, not discovered midway.

The schedule matters beyond the gut itself, because demolition is the first trade on a renovation. Framing, mechanical, and finish crews are booked against the handoff date, and every week the gut slips pushes the entire remodeling timeline with it. You can see the sequence a professional crew works through in our interior demolition process, from walkthrough and scope to protection, removal, load-out, and the broom-swept handoff.

For investors, the same math runs through the holding costs: a gut that finishes on its quoted schedule protects the renovation start date, which protects the budget the whole project was underwritten on.

Frequently Asked Questions

What is the average cost per square foot to gut a house in the Twin Cities?

Whole-house guts are not priced as a flat per-square-foot rate the way a single room can be, because depth of scope, materials, and disposal vary too much from house to house. The useful planning figure is the per-project range: $15,000 to $35,000 for the demolition portion on an average single-family home, quoted after a walkthrough. Per-square-foot figures quoted online for gut remodels mostly describe the rebuild, not the demolition.

A 1,200 sq ft home is smaller than the average home behind the typical range, so most price toward the lower portion of the $15,000 to $35,000 band when finishes are light and no abatement is needed. Plaster, tile, or hazardous materials move it up. A written quote after a walkthrough replaces the estimate with your actual number.

A standard Precision Demolition quote includes loading, hauling, and disposal of the debris created by the confirmed scope. Additional volume beyond that scope is confirmed in writing before it is billed. Always ask whether disposal is inside any bid you compare, because leaving it out is the easiest way to make a bid look cheaper.

Testing and regulated abatement are budgeted separately from standard demolition pricing. Older Minneapolis and St. Paul homes, especially those built before 1980, can contain asbestos and lead paint, and identifying them at the quote stage keeps them out of your change orders.

The general contractor pulls the permits, and Precision Demolition operates as a licensed subcontractor under the general contractor’s permit. Homeowners running their own project should confirm their city’s requirements before work starts.

Typically 2 to 4 weeks from mobilization to handoff, set by square footage, scope, and whether abatement or phased work is involved. Your contractor should commit to the timeline in the scope before work begins, because your remodel trades are scheduled against it.

Get a house gut estimate from a licensed Minneapolis demolition contractor

A range starts the budget. A walkthrough finishes it.

Precision Demolition serves general contractors, remodelers, restoration companies, investors, and homeowners across Minneapolis, St. Paul, Edina, Bloomington, Plymouth, Maple Grove, Eden Prairie, Minnetonka, St. Louis Park, Woodbury, Blaine, Lakeville, and Wayzata. Every crew is in-house, every project is quoted per scope in writing, and every gut is handed back clean and broom-swept, ready for the next trade.

Call 612-517-7680 for a house gut estimate in Minneapolis-St. Paul.

Phone: (612) 517-7680
Email: zubin@precisiondemolition.net
Request a Project Quote: Click Here

You can find our Better Business Bureau Profile here!

Interior Demolition Cost Minneapolis | Precision Demolition

Interior demolition MN

How Much Does Interior Demolition Cost in Minneapolis? (2026 Pricing Guide)

Interior demolition in the Minneapolis-St. Paul metro typically runs $2 to $8 per square foot, or $1,000 to $5,000 for an average single-room project, depending on what is being removed (drywall and framing vs. cabinetry, tile, and plumbing fixtures), disposal volume, and whether asbestos or lead testing is required for homes built before 1980.

By Precision Demolition, a licensed and insured interior demolition contractor serving Minneapolis, St. Paul, and the Twin Cities metro. Our crews are in-house, EPA Lead-Safe Certified, and OSHA 10 trained, and every project is handed back clean and broom-swept, ready for the next trade.

Most cost information online for this work comes from national directories that have never priced a job in Hennepin County or Ramsey County. The ranges are not wrong, but they do not tell you why one Minneapolis kitchen costs twice as much to demolish as the one next door. This guide breaks the numbers down the way a local contractor actually builds it. For the crew behind the numbers, meet your Minneapolis interior demolition contractor.

What factors affect interior demolition cost in the Twin Cities?

No two interiors demolish the same way, and the spread between $2 and $8 per square foot is explained by a handful of factors that show up on almost every bid.

What is being removed. Drywall and non-structural framing are the fastest, lightest materials in a building, and they sit at the low end of the range. Cabinetry, tile, stone, cast iron tubs, and plumbing fixtures take longer to remove, weigh more to haul, and push a project toward the top. Plaster and lath, common in older Minneapolis and St. Paul homes, also takes longer to take down than modern drywall.

Whether a wall is load-bearing. Removing a partition wall is straightforward demolition. A load-bearing wall is a different project because the structure above it has to be supported, and the modification itself is framing work. If your floor plan involves moving or removing load-bearing walls, expect that portion to be scoped and priced separately from the demolition.

Access and protection. A walk-out basement or a first-floor kitchen with a wide exterior door moves debris out quickly. A third-floor condo, a tight stairwell, or an occupied commercial space takes longer, because every load travels further and everything that stays has to be protected before work starts. That protection time is part of a real bid.

Disposal volume. Everything removed becomes C&D (construction and demolition) debris that has to be loaded, hauled, and disposed of. The more a project fills a roll-off dumpster, the more disposal shapes the final cost. Tile, plaster, and concrete-based materials add weight fast.

Testing for older homes. Homes built before 1980 can require asbestos testing and lead paint testing before demolition begins. If regulated materials are found, handling them correctly adds cost. This is covered in its own section below, because it is the factor homeowners least expect.

Scope clarity. Contractors price unknowns. A clear, room-by-room scope from a general contractor or remodeler prices efficiently, while a vague scope carries contingency.

How much does interior demolition cost per square foot?

The working range for interior demolition in the Twin Cities is $2 to $8 per square foot of the area being demolished. Light scopes, such as drywall, trim, carpet, and non-structural framing, price toward the bottom. Heavy scopes, such as tile over mortar beds, cabinetry, fixtures, and plaster, price toward the top.

Because there is no reliable online calculator for this work in Minneapolis, use the same simple math a contractor starts with:

Square feet being demolished x the per-square-foot rate for your scope = your starting estimate.

For example, a 500-square-foot interior priced at $2 per square foot starts at $1,000. The same space priced at $8 per square foot starts at $4,000. That spread is the scope, not padding. A 500-square-foot gut of drywall and carpet is a fundamentally different job from 500 square feet of tiled bathrooms, cabinetry, and fixtures.

Two cautions on the math. First, the figure is a starting estimate, not a quote: testing, permits, and unusual disposal can move the final number, as the sections below explain. Second, the area that matters is the area being demolished, not the size of the house. A remodel that only opens one kitchen and one bathroom is priced on those rooms.

The most accurate way to price your project is a scoped quote based on what is actually in the rooms. Before work begins, it also helps to understand what the demolition process looks like from walkthrough to handoff.

What does interior demolition include, and what costs extra?

A standard interior demolition scope from a licensed contractor should include the work that takes a room from finished to ready for rebuild:

  • Removal of drywall, plaster, and interior finishes back to the studs where specified
  • Removal of flooring, including tile, hardwood, vinyl, and laminate, down to the subfloor
  • Removal of cabinetry, countertops, vanities, and built-ins in the rooms being demolished
  • Removal of plumbing fixtures such as tubs, showers, sinks, and toilets, with disconnection coordinated with the relevant trades
  • Protection of floors, doorways, and adjacent rooms that are not part of the scope
  • Loading, hauling, and disposal of the demolition debris created by the work
  • A clean, broom-swept handoff so the next trade can start on schedule

Items that commonly cost extra, and should be confirmed in writing before work starts:

  • Asbestos and lead work. Testing, and any regulated handling that testing triggers, is separate from standard demolition pricing.
  • Load-bearing wall modifications. Supporting the structure and altering a load-bearing wall is framing work, arranged through your general contractor.
  • Permit fees. Permit costs belong to the project, not the demolition line item. More on this below.
  • Extraordinary disposal. Unusual debris volume or heavy material beyond the scoped amount can require additional roll-off dumpster capacity.
  • Work outside the confirmed scope. Rooms or finishes added after the quote are priced as a change. Knowing how to prepare for interior demolition before the crew arrives keeps that scope clean.

This is also where in-house crews matter to your budget. Precision Demolition runs every job with its own employees, never rotating subcontractors, so the scope you agree to is the scope the crew on site is working from.

How much does it cost to gut a single room vs. a full house?

An average single-room interior demolition, such as a kitchen or a bathroom, typically runs $1,000 to $5,000 in the Twin Cities. A small, light bathroom scope lands near the bottom of that range. A large kitchen with cabinetry, tile, and fixtures lands near the top.

A full house gut is priced differently because it is a different kind of project. Every room is taken back to bare studs and subfloor: drywall and ceilings, all flooring, kitchen cabinetry, every bathroom finish, doors, trim, and fixtures throughout. The right way to estimate it is the same per-square-foot math from the section above, applied to the total interior area being gutted, at the rate that matches your finishes. A house finished in plaster, tile, and hardwood costs more per square foot than one finished in drywall and carpet, and a full gut also fills far more disposal capacity than any single room.

A full house gut should never be priced as a guess over the phone. Housing age, testing requirements, load-bearing walls, and access change the number too much. A contractor who walks the property and prices the scope in writing, room by room, is protecting your budget as much as his own.

Do I need asbestos or lead testing before demolition? (MN homes pre-1980)

If your home was built before 1980, plan on this question coming up, and budget for the possibility that the answer is yes.

Older Twin Cities homes can contain asbestos in materials such as flooring and insulation, and lead paint is common in pre-1980 housing stock. Demolishing those materials without knowing what is in them creates a health risk and a regulatory problem. Testing first lets the work be planned and handled correctly.

The Minnesota Pollution Control Agency asbestos guidance explains how asbestos is regulated in Minnesota, including requirements that apply before renovation and demolition work. For lead, the EPA lead-safe renovation rule sets the federal requirements for work that disturbs painted surfaces in older homes, and it is the reason lead-safe certification matters when you hire. Precision Demolition is an EPA Lead-Safe Certified firm with OSHA 10-trained crews, so regulated materials are handled properly when they are part of a project.

Testing itself is a modest line item next to the cost of stopping a job midway because something untested was disturbed. If your home predates 1980, raise it during the quote, not after the crew arrives.

How much do permits and disposal add to the total cost?

Permits. Many interior demolition projects require a demolition permit, and requirements and fees vary by city and by scope. Permit information and current fee schedules are published by the City of Minneapolis, and St. Paul and the suburbs run their own permitting. On contractor-led projects, the general contractor typically pulls the permit, and the demolition crew works under it. Budget the current fee for your city and scope, confirmed before work starts, not a figure quoted from memory.

Disposal. Disposal is the second-highest cost most homeowners underestimate. Demolition turns a finished room into a roll-off dumpster of C&D debris that has to be loaded, hauled, and disposed of. A standard quote includes the disposal created by the confirmed scope. Costs climb when material is heavy (tile, plaster, and masonry weigh far more than drywall), when volume exceeds the scope, or when regulated materials need separate handling. Ask any contractor you compare whether disposal sits inside the quoted number or on top of it. That question explains a lot of the difference between bids.

DIY vs. hiring a licensed interior demolition contractor: what's the real cost difference?

DIY demolition looks cheaper because the labor line reads zero. The real comparison is everything else.

Renting a roll-off dumpster, buying protective equipment and tools, and paying disposal fees come out of the same pocket either way. What DIY adds is time, typically several times longer than a professional crew, and risk. Cut a line you did not know was live, disturb asbestos or lead paint in a pre-1980 home without testing, or remove a load-bearing wall you assumed was a partition, and the savings disappear into repairs, delays, and liability.

A licensed interior demolition contractor brings in-house crews who do this work daily, carries insurance, holds EPA Lead-Safe certification, protects what stays, and hands the space back broom-swept on a schedule your other trades can plan around. For general contractors and remodelers, that reliability is the real value: demolition is the first trade on the job, and every day it slips pushes the whole project back.

Frequently Asked Questions

How much does interior demolition cost per square foot in Minneapolis?

Typically $2 to $8 per square foot of the area being demolished. Light drywall and framing scopes are priced at the low end, while tile, cabinetry, fixtures, and plaster are priced at the high end.

Multiply the square feet being demolished by the rate that matches your scope: $2 per square foot for light work, up to $8 for heavy finishes. A 500 square foot space, for example, starts between $1,000 and $4,000 before testing, permits, and any unusual disposal.

A standard Precision Demolition quote includes loading, hauling, and disposal of the debris created by the confirmed scope. Additional volume or regulated materials are confirmed in writing before they are billed.

Homes built before 1980 may require asbestos testing and lead paint testing before work begins. It is a small cost next to stopping a job for untested material, and it should be raised at the quote stage.

On contractor-led projects, the general contractor typically pulls the permit, and our crew works under it. Permit fees are set by each city. Minneapolis publishes its permit information and fee schedule on its city website, and St. Paul and suburban cities do the same.

Confirm the scope room by room with a contractor who walks the project: what comes out, what stays, what is load-bearing, and what the home’s age means for testing. That scoped, written quote is what our full range of demolition services is built around.

Get a free interior demolition quote in Minneapolis-St. Paul

A range gets your budget started. A scoped quote gets your project scheduled.

Precision Demolition serves general contractors, remodelers, restoration companies, and homeowners across Minneapolis, St. Paul, Edina, Bloomington, Plymouth, Maple Grove, Eden Prairie, Minnetonka, St. Louis Park, Woodbury, Blaine, Lakeville, and Wayzata. Every crew is in-house, and every project is handed back clean and broom-swept, ready for the next trade.

Call 612-517-7680 for a free interior demolition quote in Minneapolis-St. Paul.

General contractors, give us a call to discuss your project. We move fast.

Phone: (612) 517-7680
Email: zubin@precisiondemolition.net
Request a Project Quote: Click Here

You can find our Better Business Bureau Profile here!